In the previous article, we have discussed the riveted Joint, which is a permanent type joint. In this article, we will discuss the different Advantages and Disadvantages of Welded Joints over Riveted Joints. First of all, what is a Welded Joint? Welded Joint A welded joint is a permanent joint. This welded joint can be […]
Failure of Riveted Joints
Have you ever seen the Failure of Riveted joints? That’s right. that is one of the ways it fails. There is shear in the Rivets as per the above failure picture. The following image is a sample of the Failure of a Riveted joint due to the tearing of the plate. So, there are different […]
What is Engineering Mechanics?
Engineering mechanics is a branch of science, that deals with the which deals with the laws and principles of Mechanics, along with their applications to engineering problems. As a matter of fact, knowledge of Engineering Mechanics is very essential for an engineer in planning, designing, and constructing various types of structures and machines. In order […]
ASME Codes for Piping System
In the previous article, we had an introduction to the piping systems, Piping applications, Piping Material selection, Pipe Joints, Pipe Fittings, and Piping system standards. Among the different Piping standards, One of the most used standard for the piping system is ASME B31. Which regulates the design, material selection, inspection, test and safety of the […]
Introduction to Piping System | What is piping?
After a few requests from my readers, I am finally writing about the introduction to the Piping system. As we all knew, Pipes are used to transporting fluids, slurries, and sometimes even very fine particles. The most common application we see in the piping is Plumbing in our buildings, workplaces, and many places where water […]
What are the different types of Riveted Joints?
What is a Rivet? Well, A Rivet is a permanent fastening element mostly used for fastening light metals of plates in Boiler shells, structural works, Shipbuilding, and bridges. In the previous article, we have discussed the Riveted joint method, Different Rivethead types, and the materials used for the Rivets according to the Indian Standards. In this article, we are […]
What is Caulking and Fullering in Riveted Joint?
In the previous article, we have discussed the Riveted joint method, Rivethead types, and the materials used for the Rivets according to the Indian Standards. In the Riveting methods, it is essential for some applications to make a leak-proof Riveted joint. Those applications are Boilers, air receiver tanks, and ship hulls. In order to achieve […]
What are the types of Rivet Heads according to the Indian Standards?
What is a Rivet? Well, A Rivet is a permanent fastening element mostly used for fastening light metals of plates in Boiler shells, structural works, Shipbuilding, and bridges. In this article, we are going to discuss different types of Rivet Heads according to the Indian Standards. In a permanent joint, Rivet is the fastening element. […]
Methods of Riveting and Material used for Rivets
What is a Rivet? Well, A Rivet is a permanent fastening element mostly used for fastening light metals of plates in Boiler shells, structural works, Shipbuilding, and bridges. In this article, we are going to discuss the methods of Riveting joints and what are the materials that can be used for the Rivets. In a […]
How to design an Oval Flanged Pipe Joint?
The Oval flanged Pipe Joints are mostly used in small pipes with diameters up to 175mm. This Oval Flanged Pipe Joint is mostly used in Hydraulic applications. In the previous article, we have discussed the Circular Flanged Pipe joint. To design an Oval Flanged Pipe Joint we need to determine the main parameters such as […]
How to design a Circular Flanged Pipe Joint?
The circular flange pipe joint is one of the most used flange joints among the other types of flanged joints. To design such a circular flanged joint we have to determine the main influencing factors and evaluate them. In this article, we will determine the main parameters to design a circular flanged joint for a […]
What Pipe Flange should I use based on Steam pressure according to Indian Boiler Regulation?
Is there any regulation that standardised the pipe diameter and thickness for the steam pressure? Yes, there is a regulation in India called the Indian Boiler Regulation, in short IBR which is created in 15th September 1950 to regularise the manufacturing of boilers, steam generators and steam distribution piping systems. For the manufacturers and the […]
Impact of Crude oil export on Economic Growth of Nigeria
A Final Project on “Impact of Crude oil export on Economic Growth of Nigeria” was submitted by Olawale Mudashiru (from the University of Jos, Plateau State) to extrudesign.com. 1. INTRODUCTION 1.1 BACKGROUND OF THE STUDY Nigeria economy is basically an open economy with international transactions constituting an important proportion of her aggregate economic activities. Over the years, […]
What are different Pipe Joints?
In transporting fluids such as water, steam, gases, oil, and chemicals, pipes are used. Designing a pipe with basic parameters such as the diameter and thickness of the pipe is explained in the previous article. While designing these pipes the length can be limited, there must be a way to join them to achieve suitable […]
Smart Waste Management System Based On A IoT Platform
A Final Project on “Smart Waste Management System Based On A IoT Platform” was submitted by Nikhil S Ambigar (from the Indian Institute of Information Technology,(IIIT) Dharwad, India) to extrudesign.com. Abstract Many metropolitan cities produce tons of waste every day, so efficient methods for collection and disposal are crucial. To make people’s lives happier, safer, and […]
Communication of Safety in Factories
A Final Project on “Communication of Safety in Factories” was submitted by Aaryaman Maheshwari (from Manipal University(MAHE), Manipal, Karnataka 576104 INDIA) to extrudesign.com. ABSTRACT Factories are places of risky and dangerous work which involves heavy machinery, maybe chemicals, hardware etc. It definitely has a higher risk of causing injuries and damage to human lives employed. It […]
What are the different Reticles in Metrology?
First of all, What is a Reticle? A Reticle is a Graticule that turns the microscope into a measuring device in Metrology. On the eyepiece of the microscope, there are the graduated reference lines are etched to take measurements, these are the Reticles. In this article, we are going to discuss the different Reticles with […]
What is Laser Interferometer?
Interferometry is nothing but the use of optical interference to carrying out precise measurements of very small linear dimensions. Laser Interferometer is one of the interferometers which uses laser means and electronic controls to carry out the inspection of machine parts for straightness, parallelism, and flatness, and measurement of very small diameters, among others, and also […]
Comparative Study Of Individual Investors: Physical Assets Vs Financial Assets
A Final Project on “Comparative Study Of Individual Investors: Physical Assets Vs Financial Assets” was submitted by Adhavan.V (from Sri Krishna Arts and Science College, Coimbatore, INDIA 641008) to extrudesign.com. Abstract The financial position of a country largely depends on the inflation rate, foreign exchange rate, per capita Gross domestic product, etc. Savings from middle-class households […]
Apple MacBook Air M1 Review
On November 10, 2020, Apple released the MacBook air with their own chipset so-called M1 based on ARM architecture. Previously apple used the intel chips built on the x86 architecture on the MacBooks. Here is the quick unboxing video showing the first look at the Apple Macbook Air with an Apple silicon M1 chip. Is […]
- 1
- 2
- 3
- …
- 17
- Next Page »
